综合辅导：微软认证考试:基础知识篇（3）

文章作者 100test 发表时间 2007:09:06 13:32:13
来源 100Test.Com百考试题网

31:
you are designing a wan connect 3 networks locate in chicago, atlanta andlos angeles
desired result:
all of computer on each of 3 network must be able to communication with any other computer on the 3 networks
the wan link must be capable oftransmising data at a minimum speed of 1 mbps
optional results:
.you want to provide continous communication when 1 link failure
.you want to provide continuous communication when 1 link failure at minimum 1mbps
proposed solution:

connect 3 networks using 2 primaryt1 and 2 secondary asynchronous 9600 bps link as shown below

figure 1

a: match results andmatch all optional
b: match results and one of optional
c: match resultsand none of optional
d: not match results
ans:b

32:
you are designing a wan connect 3 networks locate in chicago, atlanta andlos angeles
desired result:
all of computer on each of 3 network must be able to communication with any other computer on the 3 networks
the wan link must be capable oftransmising data at a minimum speed of 1 mbps
optional results:
.you want to provide continous communication when 1 link failure
.you want to provide continuous communication when 1 link failure at minimum 1mbps

proposed solution:
connect 3 networks using 16 port ras server at each location , as shown in exhibit
each port will have a 28.8 modem

figure 2

a: match results andmatch all optional
b: match results and one of optional
c: match resultsand none of optional
d: not match results
ans:d
33:
you are design disaster prevention and recovering plan .
network config:
server : 2 ,total run windows nt server
one is pdc , another is bdc
client : 100 ,all run windows 95
network type : 10baset
you done following .
place all confidential data on server.
place server on a locked room.
implement ntfs user-level security on servers to share resouce
desired results:
.you must prevent server form hardisk failure ,however period of down time of less than 2 hours areacceptable
.you must have resonable controls in place to protect network data from loss
optional:
.you want to trace all access of data
.you want to put reasonable methods in place to protect network data from virus corruption
proposed solution:
.connect ups to each server
.set proper access-control security on shared resources
.implement disk striping with parity fro each servers hardisks
.do daily tape backup of data,store tape in a off-site location
.implement virus scanning on all clients and servers
.enable audit on shared file
which result?
a: match results and both of optional
b:match results and one of optional
c:match results and none of optional
d:not match
ans:a
34:
you want to monitor network performance and faciliatetrouble shooting of network problems.
which tool should you use?
a: cable tester
b: volt-ohmmeter
c: tdr
d: protocol analyzer
ans:d
35:
you want communication on your network to continue even if one of you servers hardisk fails, you also want to limit costs
which type ?
a:raid 0
b: raid 5
c: duplexed hard disks
d: backup file server
ans:b
36:
the server on your network run nt server,the network use tcp/ip
the network is devided with routers into multiple subnet
what can enable client to browse netbios name on all subnet of the network ?
a: a wins server
b: a dhcp server
c: a router
d: a netbios broadcast
ans:a
37:
you want to monitor and manage the hubs , bridges , routers in you network, your server run nt server,
which should you include in your plan?
a: performance monitor
b: snmp management station:hardware.
c: protocol analyzer
d: tdr
ans:b
38:
you install a server network card, run nt server , the computer has com1,com2,lpt1,lpt2,network card
use i/o address 300 , irq 3
which conflict ?
a:vga card
b:com1
c:com2
d:lpt1
ans:c
39:
you install a network card in a client , the computers software is initial success,but the computer not able to communication with other computers on the network , all other client computers on the network are able to communication.
what is the most likely cause of problem?
a: the transceiver setting of the network adapeter is incorrect
b: i/o address
c: cablle segment not properly terminator
d: packet-size setting is incorrect
ans:d? a
40:
which tool should you use to messure network utilization?
a: protocol analyzer
b: tdr
c: cable tester
d: volt_ohmmeter
ans:a